Hi ossandust 10 , The MIDI interface is a Steinberg UR22, and usually it's pretty good. Thanks a lot for your offer to take a look at the setup file. I attached it to this answer.

Hey Jack - do you mean in the MIDI monitor? There MIDI IN --> --> MIDI OUT is not active. But I liked your thought, so I tried to deactive MIDI THRU in the Global Configuration of the fcb1010 - just

Maybe you have MIDI Thru set up on your FCB 1010. Turn it off in Uno2 Control Center. It will cause a nasty MIDI loop (I believe) if you have it on while sending the configuration.

The UnO2 firmware shows "88" when it starts receiving a patchdump, and shows the current bank number (normally 01) when the setup is loaded. If you send me your setup I can check if has an issue which

I have to turn off an on the fcb1010 after every SEND SETUP, then it works, again, so the setup was obviously sent correctly. I have tried a RESET on the fcb1010 as well, but that had no effect. Can

Attached are screenshots of how to configure a Preset and a Toggling CC (Stomp). In Amplitube you need to place your presets in the Preset Screen (SS attached). In AT5, you need to set the FX Bypass

What do you mean? The upgrade doesn't affect your computer's MIDI drivers or connections. Your old settings probably won't work with Amplitube 5, but the FCB1010 should still be able to control it.

Hi guys I recently move to Amplitube 5 from 4 but no joy on make FCB1010 work with it, is anyone have a better luck? Does any sysex file exist to upload FCB. I have on-board chip not Uno or sort :(

I can confirm that there must have been a temporary server connection issue about 8 to 9 hours ago, causing the license database to be inaccessible. Things are working correctly again, new code has

There seems to have been a server connection issue - will need to look into it after working hours. In the mean time I have blocked your license code for obvious reasons - I will send you a new code

Entered info as on the box, tells me it's incorrect. Tried Opera, Chrome and Edge. Screenshot attached.

Hi again Since William awaked my curiosity, I just setup the 10 switches of my FCB1010 to match a Tyros function. So, here is how it is done. First set the FCB1010 MIDI channel to whatever you

Hi again Here I want to share some things that I forwarded to William. In case that somebody else has a Tyros and wants to try it. On the YouTube video, not all note numbers will be shown. This means

By the way, the YouTuber also mentioned that the table can be found on page 10 of the FCB1010 manual. You can get a copy from

Dear William On my previous post, you will find a link to this video: https://www.youtube.com/watch?v=hqt-fk5ZyWk I also put the time marks were you will find all the information. You are looking for

Hi Josef Now home and red throgh your message angain carefully. Few questions thoug. - In Tyron mfc10 template you can .... send the seleced functions of all 10 buttons via midi a or b and channal

Hi William I'm also looking fordward for doing the same, but I haven't had the time yet. Anyway, I found this video: https://www.youtube.com/watch?v=hqt-fk5ZyWk It is unfortunatelly in german, but I

Hi Chris. Still strugglin ;). Cant find neede note numbers. Found some like main A-D My target is too use FCB 3 memory banks with slightly different functions. And needed assignable functions are

It seems that a few new applicants to join our group do not receive our Questionnaire email in their Inboxes and, because they don't reply to that email, they are never granted membership.

Never used Guitar Rig outside of my DAW (and don't use it much, really), so I didn't know about NI's ASIO driver. Thanks EJ.