Howdy, Is anyone out there using the FCB1010 to switch channels on a non-midi amp. I would like to switch channels on my Peavey 5150II using the controller. I know I have to custom wire the footswitch

Well, they sent me two more EPROMs and this time properly in an IC case and I've gotten them installed and am up fully to 2.2E. The install went beautifully. It was very easy mostly due to the fact th

These Nasty Flashing Ads These outfits like doubleclick put flashing ads over and under your work and use up your computer memory that you paid for and should be all yours and not theirs. Yahoo sells

I sent some questions to behringer tech support last tuesday, and haven't received any answer or acknowledgement. the adr I used was support@.... is that the best one? has anyone ever gotten an answer

Hi, Just getting up and running with my new FCB 1010. It is controlling a Switchblade 8b (www. soundsculpture.com) and I can select the first 40 presets fine. If I bank up into BANK 6 and press 3 inst

Just wanted to let anyone that didn't know that Behringer USA is distributing the latest EPROM upgrade (v 2.3.12) free for the asking. I called Tech Support (425-672-0816) on July 26th, and was told t

Yo! Just a follow up on using the FCB1010 to switch amp channels. I custom wired a 1/4" TRS plug on one end of the footswitch cable to my 5150II. The FCB1010 only has two switches, so I wired one to s

HI, I have 2 effects units I want to control with the FCB1010 and I would like to know which approach is the most effective way of doing that. Right now I programming the different commands (PC1,CC1 e

I'll be updating this this morning with the latest ROM info, etc. Apologies for it getting behind, but what with moving house, going on vacation, first gigs with the new band... -- Mike Whitaker: mode

Behringer USA took my eprom upgrades for both the fcb1010 and VAmp2 via phone last week. Arrived today. Good customer support, imo. Thanks Behringer. -joe

I just go the FCB1010 so forgive my ignorance. I use it to switch patches/presets on my processor and preamp. I hit number 1, it switches both units to #1, hit number 2, it goes to #2, etc. This is pe

OK, Just got my FCB1010 today, and already programmed some pretty cool stuff. I am having a small problem though. With firmware 2.1 (gonna call the company tomorrow for the new one...), I am using exp

hi, is there an editor for the fcb1010, or can this be done with sounddiver or something? thx, erik

I am currently using the FCB 1010 to control my Peavey midi preamp/efx and I'm having a problem calling up the correct preset numbers. The main problem is that the Peavey presets start at number "00"

beware: midi novice alert!! after a month of floundering and talking to behringer techs i can't get it to perform what i think is the simplest function. of course being midi ignorant doesn't help, i g

beware: midi novice alert!! after a month of floundering and talking to behringer techs i can't get it to perform what i think is the simplest function. of course being midi ignorant doesn't help, i g

Hi List, With recommendations from the rigtips and cybertwin lists I've recently acquired an fcb1010 for my Fender CT. I've read through the archives on this list and quickly scanned FenderForum and I

Hello all. Does anyone know if you can get Phantom Power out of the FCB1010? This is a nice feature I would like to see. Checked documentation, didn't see it. Thanks. Do You Yahoo!? HotJobs, a Yahoo!

I just bought a 1010 and want to programme it for use with my Ztar. I find the operating system impossible to understand, and the manual is worse than pathetic (and I'm a qualified trainer and adult e

I'm a guitar player. I recently bought an FCB1010, TC Electronics G-force , a Boogie Triaxis and a Boogie 2-Ninety. Being kind of new to the MIDI scene I did have a few problems getting to grips with