So we use the Midi-in port of the FCB to send SysEx messages and load presets. Is there any other reason why an actual physical midi device would be connected to the Midi-In port of the FCB?

I need to replace board EPROM is seated in. I can't find the P/N or ordering information anywhere. PLEASE HELP!!!!! -- -- Very Respectfully, Kevin Hanning, Chief-USN(ret.) Kevin.hanning@... Phone: (57

Has anybody ever used the FCB to run Garage Band on an iPad? Any hints?

There's a whole page in the manual for the FCB Editor (from the mountain utilities website) that talks about various midi inputs and outputs and how to avoid the midi feedback loop and all. Say you're

I can't find the ordering information anywhere for the main board. Someone please point me in the right direction. -- -- Very Respectfully, Kevin Hanning, Chief-USN(ret.) Kevin.hanning@... Phone: (573

I have FCB1010 + UnO (1.0.4). Using the FBC/UnO Control Center app on Windows. I'm trying to send the following event in this sequence: CC 000 063 CC 032 068 PC 001 The problem is that the FCB is send

How can I configure a footswitch on the FCB1010 to send CC events before PC events? I want to sent: CC 000 063 CC 032 068 PC 001 I'm using the FCB1010 + UnO 1.4 + UnO Command Center to send CC and PC

Hello, my expression pedals responds and transmit numbers from 0 to 127 but only from exactly the half way and up, means that the first half way the pedals move but nothing is happening, Thus I lose h

Ok, so it was pretty easy to save a back up file on the computer using Midi OX. Then I did a factory restore and tried to send back one of the back up files. According to the manual , once the stored

Hello Everybody Sorry for my bad english. It is my second language I bought a used Behringer fcb1010 ( v2.5 ) that i try to use with amplitube 4 I used this video to help me: https://www.youtube.com/w

you wrote: Sensors might be mis-aligned. Try the suggestions mentioned here : http://www.vivid-abstractions.net/logical/how-to/how-to-behringer-fcb1010-expression-pedals-not-working-even-after-calibra

Hello there, I purchased the FCB 1010 and I have a problem/question which I couldn't find an answer to in all forms/FAQs that I visited and read- Both expression pedal on my device DO transmit a full

In order to get into the Preset Editing Mode, we select a button...press and hold "DOWN" and that takes us to the editing mode for the selected preset. For programming Exp A & B pedals , we still have

Hello. Please forgive if this is a dumb question (or a repeat -- I couldn't find this issue in the history). I purchased an UnO Chip on eBay. I can assign stompbox mode to either the upper or the lowe

Basically I selected PRESET 1 and went to the preset editing mode.....Activated SWITCH 1 . The FCB is connected to the foot pedal input on a Fender amp. Now PRESET 1 acts like an ON switch for the eff

I have the standard stock model. It's midi'ed to a keyboard. Certain parameters such as sounds and preset can be remotely selected via an external controller such as FCB. The thing is they require a s

Hi there, I first noticed the problem when Ableton started playing for apparently no reason. It was like I'd clicked "play everything". So I opened up MIDI Monitor (on my Mac) and noticed that in addi

I have the latest stock firmware. I've seen the instruction for calibrating the pedals so I know how it's suppose to be done. I think I read in the FAQ section that certain units had issues with their

Hi does anyone have any experience of this combination, I've just bought an fcb1010 I particularly want to be able to turn the effects on and off within patches on the DG80. I've just ordered a uno ch

Anyone set up the FCB1010 as a DAW controller? I am considering setting up to control Samplitude. Suggestions? Templates? Thinking maybe one row for play, stop, record, rew, ff, and one for efx? Have