Date   

Re: FCB1010 Uno with Amplitube

EJ SHELDON
 

How are you connected to the computer? Audio Interface with MIDI (brand/model - not all will pass sysex)? Dedicated MIDI Interface (most will pass sysex)? $5 ebay MIDI/USB interface (most will not pass sysex)? This is important.

The Ed Dixon Editor won't work with the UNO Chip - that's why it says "Unknown Version". You NEED the ControlCenter Editor to make this work.


Re: FCB1010 Uno with Amplitube

Nala Lee
 

Right now I only have FCB-Midi Out to PC-Midi In connected and FCB1010 PC Editor shows Firmware: Behringer - Unknown Version.

Thankfully I have an extra Midi cable going to my edrumset, I will use it to connect PC-Midi Out to FCB-Midi In to download the syntax file.

If I have any trouble with the download, I will try the method you mentioned!

Thank you!


Re: FCB1010 Uno with Amplitube

EJ SHELDON
 

BTW - IDK what MIDI interface you're using, but you'll need a 2 way connection to use an editor, and not all interfaces will handle the longer sysex files. If your interface won't connect to the editor, that could be the reason. If it connects but won't DL the sysex to the FCB, there's an option in ControlCenter to send the sysex in smaller chunks that may help.


Re: FCB1010 Uno with Amplitube

Nala Lee
 

Thank you for the guide and the attachment!  

I will give it a try when I get home!!!


Re: FCB1010 Uno with Amplitube

EJ SHELDON
 

First, get the UNO_ControlCenter Editor:


Read the manual.

Then, open the attached .lgp (ControlCenter sysex) file and download it to your FCB/UNO board.

If you're using Amplitube in standalone mode, you'll want to set the Receive Channel in Amplitube to Channel 1.

This sysex is configured with the STOMP pedals on the bottom row.

Click MIDI (lower right on AT (Amplitube) UI, Click Control Change then Global.
If you're in Bank 00, hit the DOWN pedal once to go to Bank 18.
Highlight PRESET NEXT. Click LEARN. Press Pedal 10.
Highlight PRESET PREVIOUS. Click LEARN. Press Pedal 9.
Highlight VOLUME. Click LEARN. Operate LEFT EXPRESSION PEDAL.
Highlight WAH. Click LEARN. Operate RIGHT EXPRESSION PEDAL.
Highlight WHARMONATOR. Click LEARN. Operate RIGHT EXPRESSION PEDAL.
*NOTE - Typically, you won't have WAH and WHARMONATOR on the same preset.
Highlight TUNER. Click LEARN. Press Pedal 8.

Press UP pedal to return to Bank 00.

Highlight Stomp A Slot 1 Bypass. Click Learn. Press Pedal 1.
Highlight Stomp A Slot 2 Bypass. Click Learn. Press Pedal 2.
Highlight Stomp A Slot 3 Bypass. Click Learn. Press Pedal 3.
Highlight Stomp A Slot 4 Bypass. Click Learn. Press Pedal 4.
Highlight Stomp A Slot 5 Bypass. Click Learn. Press Pedal 5.

Done!

NOTE: The CC#s I'm using are taken from the non-reserved segment of CC#s as specified in the MIDI spec.

Advice: Create a folder called MY PRESETS or something like that. When creating new presets or modifying Factory Presets, always save them to this folder. This way, all your Factory Presets and folders remain pristine.

In order to call Presets, you need to load them into the MIDI/Program Change.panel.

Have Fun!



.


FCB1010 Uno with Amplitube

Nala Lee
 

Hello!


I recently purchased a FCB1010 and just installed UNO chip.


I have midi out of FCB connected to midi in of my PC and have been trying to use it with amplitube.


I want to use the stompbox mode to control individual effects on and off.


Could someone guide me with how I can set up the pedal to do so and what software I need to install to make the changes to the pedal?


Thank you!


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

Here's the link for the Editor:


And the Chip:


Although you can get the chip slightly cheaper on ebay, I HATE PIRATES.
Buy it from the creator.

Be careful installing it. FOLLOW THE DIRECTIONS!



Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

Alexandar Draskovic
 

Not really (about the questions part), you answered it all in this really cool post up above. Ok, so i've tried everything & that's it. I'll have to order Uno chip...there is nothin' else really :)
Again, BIG THANK YOU for going in depth on this matter. So although Uno4Kemper will work (at least you can change presets & expression pedal works) the Stompbox mode will not. 
Tnx rd2rk for your input on all of this, time to get Uno & Uno CCEditor.
Cheers, Alex


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

Apparently the Kemper chip numbers it's presets from 0(000), while the GSP numbers from 1(001).
According to the GSP manual, PC#s 1-99 access USER PRESETS 1-99, and 101-128 access FACTORY PRESETS.

That means that, assuming that the Kemper chip works like the UNO chip, you should have 19 banks of 5 presets (95 total presets, 0-94) on the FCB. You can verify that by going up through the banks and pressing the preset buttons while monitoring the results in MIDIOX.

Each bank should, if I'm guessing right about the way it's configured, send the same 5 CC#s in each bank.
So, now you have to decide which GSP presets you want to map to which PC#s sent by the FCB, and which GSP controllers you want to map to the 5 CC#s and 2 Expression pedals (use MIDIOX to see what they're sending) on the FCB. 

UNFORTUNATELY, it appears that the Control Change messages are sending values of 0 and 1 (in your picture CC#30 was sent twice, values 1 then 0). You said that you were able to turn an effect OFF, but not back ON? If so it's because the GSP expects standard MIDI Toggling message values of 0-63=OFF and 64-127=ON (confirmed in the MIDI Implementation chart). Since 0 and 1 are both in the OFF range.....

So, do you want to get the UNO Chip? You'll also want the UNO_ControlCenter Editor (TRUST ME ON THAT! Ed Dixon will not work!). Together around $50.

The UNO Chip can be configured like the Kemper chip - each bank sending 5 PCs and 5 CCs - but which PCs and CCs are totally at your discretion through the editor. The CCs can also be configured to mimic 2-way communication - LEDs will APPEAR to reflect effect's ON/OFF status.

OR it can be configured like the stock chip, 10 banks of 10 messages, again at your discretion. 

There are advantages and trade-offs to each method, depending on your needs.

There's also a probability that you'll need a proper MIDI interface. Those cheap Chinese ones are iffy. I have two, physically identical, but only one will even CONNECT to the editor. Go figure. 

Questions?


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

Alexandar Draskovic
 

I'm using some cheap Chinese (i guess) MIDI interface, it says "VIEWCON", but it works (that's the only one i could find atm) I've attached a picture, showing presets 1-5, & stomboxes 6-10.

Again, tnx rd2rk for helping me out!


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

Craig - I'm sure it wasn't your intention to hijack Alexander's thread, but at this point I am no longer sure who I'm responding to, and that's probably confusing Alexander too.

If you have further questions concerning the GX112, please open a new thread.

Thanx!


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

CRAIG DENNIS
 

I will let you know when I figure out how to do that.  Thank you

Craig Dennis
724-288-4791 (cell & text)
412-343-1200 x 213. (Work)
Craig Dennis’ Exclusive New and Used Car Deals @ Three Rivers Chrysler Jeep Dodge Ram
2633 West Liberty Avenue
Pittsburgh, Pa.  15216


On Jun 3, 2019, at 1:42 PM, bluesrock13@... [fcb1010_uno] <fcb1010_uno@...> wrote:

 

What happens when you load the Ed Dixon Editor? Can you see a Version#? Can you see the button settings?


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

CRAIG DENNIS
 

Thank you

Craig Dennis
724-288-4791 (cell & text)
412-343-1200 x 213. (Work)
Craig Dennis’ Exclusive New and Used Car Deals @ Three Rivers Chrysler Jeep Dodge Ram
2633 West Liberty Avenue
Pittsburgh, Pa.  15216


On Jun 3, 2019, at 12:36 PM, bluesrock13@... [fcb1010_uno] <fcb1010_uno@...> wrote:

 

I'm not sure who I'm talking to - Craig or Alexander?


Craig - I've never used that amp, but the FCB should work fine with the GX112. Just perform a factory reset by booting the FCB while holding down buttons 1+7.


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

QUESTION:
What Brand/Model MIDI Interface are you using?

Attached is a series of screenshots to help you get started using MIDIOX.
If, when you open MIDIOX, it looks like 1MIDIOX, click the icon that the red arrow (my add) points to. This will open the Input Monitor Screen. It should now look like 2MIDIOX.

The other shots should be self-explanatory. After you click OK on 5MIDIOX, press ALL of the FCB buttons consecutively. If you look at 6MIDIOX you'll see that Control Change messages look different than PC (program change) messages. Your colors will likely be different, but the data types should look like the picture.

Take a Screenshot, save it to PAINT and send it to me.


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

Alexandar Draskovic
 

Nothing really, it doesn't recognize it at all...
I have made to work somehow...I can only turn the effect OFF (i've tried it with distortion), but i can do it only once...i don't know if this makes any sense?!
For eg.
I've load up the desired patch, and i want to turn on/off my distortion... I've programmed controller 6 for it...when i press it once it deactivates the dist. , but when i press it again - nothing happens... I cant turn it back on again...then i have to change the preset, and again, change it back to previous preset & again, i can only turn it off...ive googled it -  it has to do with some note on/off thing...the real question is, how do i turn on/off note for every CC? 


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

What happens when you load the Ed Dixon Editor? Can you see a Version#? Can you see the button settings?


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

Alexandar Draskovic
 

Ok, so i got the MIDI-USB cable from a friend, and it works! 
So i pushed all buttons and this is the result 
https://prnt.sc/nx40tx
preset change is 1-5
and cc is from 6-10
I Hope this make scence, b/c now i have some values, but what do i do with it :D
I know this is the pain in the butt, and @rd2rk i thank you for your time on this!


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

I'm not sure who I'm talking to - Craig or Alexander?

Craig - I've never used that amp, but the FCB should work fine with the GX112. Just perform a factory reset by booting the FCB while holding down buttons 1+7.


Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

EJ SHELDON
 

MIDI is not carried along with audio. I'm assuming that the MIDI-USB cable is one of those with a capsule between the DIN connectors and the USB connector. These will transmit basic MIDI messages, but won't necessaily transmit the longer sysex messages required fot use with the FCB Editors. What brand/model did you get?



Re: FCB 1010 (Uno For Kemper) with Digitech GSP 1101

CRAIG DENNIS
 

Have you used the fbc1010 with a Behringer blue devil amp?

Craig Dennis
724-288-4791 (cell & text)
412-343-1200 x 213. (Work)
Craig Dennis’ Exclusive New and Used Car Deals @ Three Rivers Chrysler Jeep Dodge Ram
2633 West Liberty Avenue
Pittsburgh, Pa.  15216


On Jun 3, 2019, at 9:26 AM, alexandar.draskovic@... [fcb1010_uno] <fcb1010_uno@...> wrote:

 

Update:
Ok so i have tried everything, but I just can't make FCB 1010 to run with MIDI OX...I have done correct cabling (put it trough GSP1101) and made GSP1101 my sound card, but nothing is happening when I push pedals on FCB. I have ordered Midi to USB cable to hook it up directly to the computer..I've run it through Browser Mode, Performance Mode, i've performed factory reset...nothing. I'm waiting for the Midi - USB cable, to see if this will work directly into the computer. 

1161 - 1180 of 9111