I get it. I'm in a Pink Floyd tribute and I literally can't remember the setup for each song without programming it in advance. I'm going to grab the UNO2 soon to check it out, but it sounds like

On Tue, Feb 23, 2021 at 01:39 PM, jeroen@... wrote: since my Midi-interface (E-MU Xmidi 2x2, powered by Firewire, on Mac Pro Mojave) is giving these timeout’s on the testpage:

It seems easier to unplug the MIDI cable than to go to the editor and write a command to disable MIDI Thru. But I'm probably missing something here? (in a TinyBox setup this is part of the more

I’m followig different discussions and advice here now for a while. I need to do the following: As a guitar teacher, get some basic switch functions in Guitar Rig 6 and FCB1010. (Firmware

All the other FCB1010 firmware versions allowed MIDI Thru to be turned off. Reading through the manual, it seems that it doesn't - MIDI Thru is always on. Any chance this can be added? (Feature

Hey Dan, Thanks for the reply! I checked out the Gordius - shame they are all now discontinued. Ossandust responded after your post and confirmed that the Uno2 equipped FCB just passes MIDI thru - so

Solved, it was just a problem of having special characters in the user name - the current license server converts such characters, that was not yet the case 5 years ago.

The Gordius Little Giant is indeed fully remote controllable : you can select songs or banks, select presets, activate effects, press LittleGiant footswitches by sending MIDI messages to the device.

Hey Shayne, I'm using Bandhelper to trigger the Gordius Little Giant with AxeFXII. UNO2 is based on the Gordius - all from Ossandust genius. I can verify that Bandhelper works with the Gordius, so

Hey! That serves me right for assuming…. I was sure that the FCB could accept a bank change from another device, however if it’s a MIDI THRU only device than I can work around it… My

It looks to me like the FCB/UNO2 simply acts as a "MIDI THRU" device, and "SENDS" on whatever CHANNEL the device you want to control "listens" on per this line in the code: CHANNEL DeviceName = X With

Hey All, I'm new to the forum and have some MIDI experience (not a guru by any means, but I can generally make everything work) I'm wanting to control the FCB Banks/Patch select using Band Helper via

From the UNO2 Manual: APPENDIX : Factory reset, self-test and pedal calibration The UnO2 firmware contains the same self-test and expression pedal calibration procedures as the original Behringer

After switching it off and on again, it works with the uploaded setup. 88 is not flashing Same behaviour after RESET (Power up with 1+6 pressed)

Hi. I have got the similar problem on windows7 ! I buy licence for V1. in 2016 , and then I was programing my FCB 1010uno (v 1.0.4) and further I dont need editor because the controler is work OK.

Don't forget that if you use a MIDI Note message instead of a CC, Ableton will ignore the Note Off message sent on a normal button release. If you use Note but set it to Toggle, the second press will

There aren't any specific guides because a.) Ableton is very flexible and has a lot of different included instruments, all of which can be customized in many different ways, and b.) There are at least

With the regular UNO chip, if you hit Bank Down from the first Bank, it would go the the Last bank and vice versa. I'm guessing that the DIRECT function is why this doesn't work anymore. Is there a

Thanks for the offer, Jack. I actually got the FCB UNO2 working with Live earlier today. I ended up modifying a setup file that another user had shared by making just a few important changes. I

I wonder if you could create a Bogus Effect like EFFECTS = { MYLED STATE } And then in a trigger add: SWITCH_ON MYLED STATE The only question I would have it to assign which pedal you are switching