Date
1 - 9 of 9
Only note off being sent
|
Sam Greene
I tried with the midisport and was successful - thanks all!
On Aug 22, 2022, at 03:40, ossandust <ossan.dust@...> wrote:
|
|
|
|
ossandust
On Sun, Aug 21, 2022 at 03:18 PM, Sam Greene wrote:
Should I try another MIDI interface?I checked the ControlCenter sourcecode. If the sysex gets corrupted during transmission (= interface problem), ControlCenter reports "Patchdump failed". If the issue is as described above (= setup not correctly stored, probably an FCB1010 hardware issue), ControlCenter reports "Download failed!". You can try setting the Note velocity directly on the unit, instead of using an editor. If that succeeds, you know the problem is with the interface and not with the FCB1010. |
|
|
|
Sam Greene
Should I try another MIDI interface? I see there is a list, which indicates there are some that don't play nice. I got a super cheap USB to MIDI dongle off Amazon. I have a rack unit Midisport I believe I used before.
From: uno@fcb1010.groups.io <uno@fcb1010.groups.io> on behalf of ossandust <ossan.dust@...>
Sent: Saturday, August 20, 2022 8:55 AM To: uno@fcb1010.groups.io <uno@fcb1010.groups.io> Subject: Re: [fcb1010_uno] Only note off being sent fcb control center says the dump was unsuccessfulAs opposed to other editors, FCBControlCenter does a double check : after doing a patchdump ControlCenter again requests the stored setup from the FCB1010 and compares sent and received data byte by byte. If at least 1 byte is different, it reports an unsuccessful patchdump. This might for instance occur when part of the setup memory has gone defective resulting in some settings not being stored. Or when you forget to enable "SysEx Receive" - this was necessary up till UnO v.1.0.2.f |
|
|
|
ossandust
On Sun, Aug 21, 2022 at 12:30 AM, chrisw_63 wrote:
when you don't connect both In and Out MIDI portsin that case ControlCenter would show a timeout error when trying to connect |
|
|
|
chrisw_63
On Sat, Aug 20, 2022 at 03:55 PM, ossandust wrote:
Or when you forget to enable "SysEx Receive"OR when you don't connect both In and Out MIDI ports.. haven't seen that asked yet, so may as well check. |
|
|
|
ossandust
fcb control center says the dump was unsuccessfulAs opposed to other editors, FCBControlCenter does a double check : after doing a patchdump ControlCenter again requests the stored setup from the FCB1010 and compares sent and received data byte by byte. If at least 1 byte is different, it reports an unsuccessful patchdump. This might for instance occur when part of the setup memory has gone defective resulting in some settings not being stored. Or when you forget to enable "SysEx Receive" - this was necessary up till UnO v.1.0.2.f |
|
|
|
Sam Greene
Yes - I saw that I had it set to 0 and then changed it and dumped, but it seems to not have taken effect. I’ll note that fcb control center says the dump was unsuccessful, but I see the unit react and changes are taking effect - except this
one. Says I’m on uno version v.1.0.2.f.
On Aug 20, 2022, at 04:13, ossandust <ossan.dust@...> wrote:
|
|
|
|
ossandust
With UnO firmware you can change the NoteOn velocity value - it's a global setting. Set it to a non-zero value.
|
|
|
|
Sam Greene
Hi,
I am only getting note off / 0 velocity notes. Two per press. Any ideas on what is wrong? I have an old uno version and using fcb control center. Thanks, Sam |
|
|