Need some help. I've got UnO 1.0.4 chip and have purchased both Control Center vr1 and vr2. I've been unable to keep my registration saved in Control Center. Works great until the local host name of m

Hello, This email message is a notification to let you know that the following files have been updated in the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/VERGLEICH Firmwar

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/FCB UnO ControlC

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/FCB1010 UnO v.1.

Hi all, I just got an FCB1010 and uno 1.0.4 chip and I'm trying to get them set up for stomp box mode. I installed the chip and went through an UnO initialization procedure I found, and it seemed to g

Issue Summary: I’m trying to use my FCB1010 to control a Boss RC-202 looper using CC. After receiving a CC message, this device requires a ‘reset’ message before it will accept a new CC message. Sendi

Hello, Does anybody has got the "old" version of the FCBUnoControlCenter software? Could that person place it in the Files section? There is now a "new" 2.0 version with no improvement. But you will h

Welcome to our new home everyone! Here’s a little welcoming gift for you all. My setup, as follows: Banks 00-03 are 40 Program changes on Midi Channel 1. I use these to control my software synth prese

I am trying to get some type of communication/connection with my FCB1010 and Guitar Rig 5 but nothing seems to work. I'm not getting any communication with the FCB1010 in Amplitube 4 either for what t

Hello all. Just joined the group, so my apologies for asking something that has no doubt been asked and answered too many times to remember over the last 10 years or so! I have bought the FCB1010 and

It's been a pleasure owning this board all these years, but I don't see why Yahoo is even leaving it up for email communication. Thanks to Ossandust for writing the chip code and to Mike R for startin

The GIO Transfer Agent membership application has been processed and "it" has joined the group as a regular member, which I've then followed up with changing its status to moderator in order to procee

Got a 2nd FCB1010 (for free). I'm used to the Uno f/w (1.02 or .03, I forget) on my other FCB but have been also considering the EurekaProm v3.2 for the 2nd FCB. The only thing stopping me is that the

Assuming that the new format here will essentially make it useless, my advice is to join TGP (The Gear Page). Post questions in the Digital and Modeling Forum.

First off, apologies for my MIDI newbieness. I only received my FCB1010 and UnO a few days ago but I'm hit with a wealth of problems despite hours of googling. Currently I'm experimenting with control

Hi, I found I was able to connect my FCB-1010 to my Peavey VYPYR VIP-1 in place of a Sanpera Pedal. The VIP-1 has a 7 pin MIDI port so I had to create a special 5 pin to 7 pin cable by splicing a my 5

I have a particular workflow I want to achieve and I’m trying to understand if it could work with FCB+uno+clyphx. I want to have three independent guitar tracks controlled in bank 0 and three independ

Hi Anyone figure out how to use the FCB1010 with the looper function in Amplitube? I'd like to be able to assign pedals to start/stop/play/record etc but can't find a way how to do this... thanks! Daf

This may not be possible... It seems that at some earlier version of the UNO firmware it may have provided an option to send SYSEX messages, but that functionality was removed due to storage limitatio

Just installed a new UNO Chip in my FBC 1010 controller and I am still not seeing any activity on the EXP Pedal in the UNO Control Center. I also bought the EUREKA Prom and the EXP Pedals work fine wi