I really love the tipswitch function that comes with UnO2. Unfortunately it seems that the dead range (zone between max value and the tipswitch) is fixed in angle. I want to stick some foam beneath th

The attached pdf is my template for using my FCB1010 with the new UnO2 chip with my Axe-Fx II. Having a template established makes building your setup easier by simply adding or taking away. To see fo

Hello there, I've sat down and tried program the chip again. I want to control a Line6 Helix Stomp for now (and maybe later a DMX controller...) and want to emulate stompboxes, i.e. I want to be able

A question was asked in a FCB1010 Facebook group about is there a way to send a note where it stays on when released and press again to turn the note off like a stomp box and this was what I found and

I seem to have FCB, ControlCenter, Midi interface, Mainstage all connected: if I press a button on the FCB, Mainstage registers activity. So what I want to do is press a button on the FCB that presses

been using for atleast a year with no problems. Now it's behaving very strangely. -Stompbox mode is gone -not all the buttons work for patch change Is there a reset procedure for the chip? I also trie

Hello everyone, I seem to be having a problem with Direct Select. I do not want to use this mode. From the editor I send a sysex to the FCB with the Direct Select unchecked. Editor confirms the file w

( Sorry for the double post but I thought this message might be relevant for both FCB1010 groups ) I just released brand new firmware. "UnO2" is not a successor for the current "UnO" firmware. It's a

Can you still use the FCB as a slave with the uNo eprom?

This post explains how to set up the MIDI channels, program a preset, set expression padel A for volume and the most common problems https://prezhost.com/2020/05/11/guide-to-the-fcb1010-2/

Do you want to set up your Behringer X-Air mixer to be controlled from the X AIR app on you mobile device? Here are simple steps to help you do just that. https://prezhost.com/2020/04/19/set-up-behrin

I'm trying to set up the expression pedals, and as far as I understand the LEDs shoud turn on when you enable the pedals in the software but my won't turn on, and I get no response from the actual ped

Hi dear community! Recently I bought UNO chip v. 1.0.4 and trying to control some stomps on TH-U Overloud. I am new to MIDI, so It's difficult to me grasp some basics. I uploaded My.THU.syx file to Co

Hi! I've read this snippet of the manual for Uno chip v.1.04 but still it is not clear to me. " A special case of “momentary toggling’ is implemented: in this mode, a CC message with programmed value

Learn how to take control of the expression pedal and how the volume pedal can be hacked and converted to an expression pedal. https://prezhost.com/2020/03/27/expression-pedal-basics-take-control/

Hi everyone, I got an FCB 1010 with 1.0.2.f UnO Firmware, no Control Software for now. I'd like to use it in stompbox mode in the lower row, to activate / deactivate stomps in TH-U Overloud, using the

This guide walks through sending and receiving a sysex dump with MIDI-OX in order to back up presets on the Code. https://prezhost.com/2020/03/14/sending-and-receiving-sysex-dumps-with-midi-ox/

Do you want to calibrate the expression pedals on your Behringer FCB1010? Here are the steps below to https://prezhost.com/2020/03/10/the-expression-pedals-on-behringer-fcb1010-midi-foot-controller/

This article covers the use of a FCB1010 running UnO firmware and one Boss FV500 as an extra expression pedal (connected via the pedal jack). My goal was to set up the FCB1010 to work exactly the same

I am trying to get some type of communication/connection with my FCB1010 and Guitar Rig 5 but nothing seems to work. I'm not getting any communication with the FCB1010 in Amplitube 4 either for what t