Hi everyone, I got an FCB 1010 with 1.0.2.f UnO Firmware, no Control Software for now. I'd like to use it in stompbox mode in the lower row, to activate / deactivate stomps in TH-U Overloud, using the

This guide walks through sending and receiving a sysex dump with MIDI-OX in order to back up presets on the Code. https://prezhost.com/2020/03/14/sending-and-receiving-sysex-dumps-with-midi-ox/

Do you want to calibrate the expression pedals on your Behringer FCB1010? Here are the steps below to https://prezhost.com/2020/03/10/the-expression-pedals-on-behringer-fcb1010-midi-foot-controller/

This article covers the use of a FCB1010 running UnO firmware and one Boss FV500 as an extra expression pedal (connected via the pedal jack). My goal was to set up the FCB1010 to work exactly the same

I am trying to get some type of communication/connection with my FCB1010 and Guitar Rig 5 but nothing seems to work. I'm not getting any communication with the FCB1010 in Amplitube 4 either for what t

Overview The FCB1010 is a MIDI controller pedal. It is used to control other MIDI gear like guitar modelers, MIDI capable guitar amps, rack mounted effects units and synthesizers. The most common use

Ok, not sure if I have a mechanical issue or setup issue. I have an FCB1010 with an UnO 1.0.4 chip. Everything's working great except expression pedal B (the furthest one from the switches). I'm only

Anyone still have a ripwerks file I can look at to setup up looper controls on bank 0. I have my FCB1010 setup with stompbox top row and AXE-FXII scenes bottom row. I have bank 0 free and not in use s

As stated presets 1-9 show on the display as ( 00 - 09) the next 10 show as ( 00. - 08.) I can't get it to display the 10's digit. I'm using uno chip with the Ripwerks program which works perfectly wi

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /H&K GMD40 - FCB1010 UnO/FCB1010-UnO-H&K_G

good day fine people, I have recently replaced the original chip with uno v1.0.4. Something seems to be wrong though, I was expecting to be able to scroll through banks and use the pedalboard as a sto

Hello, This email message is a notification to let you know that the following files have been updated in the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/FCB1010 UnO v.1.0

Hello, This email message is a notification to let you know that the following files have been updated in the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/FCB1010 UnO v.1.0

Hello, This email message is a notification to let you know that the following files have been updated in the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/VERGLEICH Firmwar

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/FCB UnO ControlC

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /UnO firmware information/FCB1010 UnO v.1.

Hi all, I just got an FCB1010 and uno 1.0.4 chip and I'm trying to get them set up for stomp box mode. I installed the chip and went through an UnO initialization procedure I found, and it seemed to g

Issue Summary: I’m trying to use my FCB1010 to control a Boss RC-202 looper using CC. After receiving a CC message, this device requires a ‘reset’ message before it will accept a new CC message. Sendi

Hello, Does anybody has got the "old" version of the FCBUnoControlCenter software? Could that person place it in the Files section? There is now a "new" 2.0 version with no improvement. But you will h

Welcome to our new home everyone! Here’s a little welcoming gift for you all. My setup, as follows: Banks 00-03 are 40 Program changes on Midi Channel 1. I use these to control my software synth prese