Hello all. Just joined the group, so my apologies for asking something that has no doubt been asked and answered too many times to remember over the last 10 years or so! I have bought the FCB1010 and

It's been a pleasure owning this board all these years, but I don't see why Yahoo is even leaving it up for email communication. Thanks to Ossandust for writing the chip code and to Mike R for startin

The GIO Transfer Agent membership application has been processed and "it" has joined the group as a regular member, which I've then followed up with changing its status to moderator in order to procee

Got a 2nd FCB1010 (for free). I'm used to the Uno f/w (1.02 or .03, I forget) on my other FCB but have been also considering the EurekaProm v3.2 for the 2nd FCB. The only thing stopping me is that the

Assuming that the new format here will essentially make it useless, my advice is to join TGP (The Gear Page). Post questions in the Digital and Modeling Forum.

First off, apologies for my MIDI newbieness. I only received my FCB1010 and UnO a few days ago but I'm hit with a wealth of problems despite hours of googling. Currently I'm experimenting with control

Hi, I found I was able to connect my FCB-1010 to my Peavey VYPYR VIP-1 in place of a Sanpera Pedal. The VIP-1 has a 7 pin MIDI port so I had to create a special 5 pin to 7 pin cable by splicing a my 5

I have a particular workflow I want to achieve and I’m trying to understand if it could work with FCB+uno+clyphx. I want to have three independent guitar tracks controlled in bank 0 and three independ

Hi Anyone figure out how to use the FCB1010 with the looper function in Amplitube? I'd like to be able to assign pedals to start/stop/play/record etc but can't find a way how to do this... thanks! Daf

This may not be possible... It seems that at some earlier version of the UNO firmware it may have provided an option to send SYSEX messages, but that functionality was removed due to storage limitatio

Just installed a new UNO Chip in my FBC 1010 controller and I am still not seeing any activity on the EXP Pedal in the UNO Control Center. I also bought the EUREKA Prom and the EXP Pedals work fine wi

Does anyone know if this is a 32 bit or 64 bit program. 32 bit programs will not work when the new Mac operating system comes out this fall. I am a total newbie to MIDI, so I’ve got a steep learning c

I did download another control center and I did check the midi output and it also did not work for the expression controllers. I also opened up the unit to make sure that all the harnesses were in pla

As I mentioned, the CC VALUES on the stomps are ignored by BIAS. All BIAS does is look for the assigned CC# and flip the effect status - if it's ON then it turns OFF and vice versa. If you're setting

V1.0.4 is the latest. Yes, the pedal movement should be visible in the monitor, as in the attached screenshot (SLOW movement of the pedal – the display looks weird if you move it fast, but that in its

I managed to get your config working think it was a bad MIDI connection, however no joy with the EXP pedal, same thing , I can toggle the Volume pedal on and off but cannot get the values to change fr

Thanks for the reply, I uploaded the SYSEx file you sent I reset my stomps in BIAS FX using the “Learn” option to reassign all the new CC values, but now nothing works. With the Configuration I had at

Hi, I am working in Bias FX and I want to assign an EXP Pedal to a Volume pedal. I assume you would need to assign the Vol Pedal to an effects block and then define the range, is this correct? Also wh

You've picked the most labor intensive configuration. So, I set up three banks, as follows. When you get UNO_ControlCenter you can fill out the other banks by simply using the Preset Copy/Paste functi

Yes, you can put any PC# on any FCB Preset Pedal. You can do that manually (read the FCB manual - Good Luck!) OR you can DL an editor. IF you have the STOCK FCB chip, go here: http://host.mtnsys.com:8