I am a MIDI and FCB1010 newbie, so please bear with me ... Today I installed the UnO2 v1.2 chip into my Behringer FCB1010, and then connected it to my PC (MIDI in>out, MIDI out>in). I registered the f

This is really a feature request for Uno2: I would like the Effect stomp to be a tri-state, Off (led off), Armed (led blinking), On (led on). I can do this with the Eureka chip, but had to write my ow

So I have just discovered that MIDI Monitor has a feature that lets you send test MIDI messages to DAWs etc without using the FCB1010 (or send any tests to the pedal) - which is great, except that I c

I’m attempting to use the Looper plugin in Live with FCB1010/UnO2 and getting some odd behaviour. I have a switch set as a trigger to send out a single MIDI message (controller CC number 63, value 127

I would like to use the FCB1010 with UNO chip to control the Overloud TH-U plugin in Ableton Live 11. After a long time I found out that I had to put fcb1010 files in Ableton's MIDI Remote Scripts fol

I am using Scuffham VST in Ableton Live and had good success using the 'stock' non UNO FCB 1010 board to select different presets and control Ableton easily. What I was missing was a stomp mode where

Hiya, my volume pedal works fine but my Exp pedal is only doing 0 (down) and 127 (up). Do I just need to do a 1/3 calibration or is there something else?

Hello All The problem is really explained by the topic title. every so often when either of the expression pedals is in a certain position I can see that the display is oscillating between two values.

Hallo. I can't configure the controller with MOBIUS and I'm very new to midi ... Any help ?

Hi all, Brand new here and attempting to get my FCB-UnO up and running with Amplitube 5. Any suggestions would be extremely helpful as I am very new to this sort of thing. I purchased the FCB/UnO Cont

Hoping someone has some experience programming Uno 2 to control LoopBack plugin in MainStage? Here's the challenge that is frying my brain (which admittedly is quite small): There are two transport bu

It would be great to get some advice on using conditional statements, as I can express in English what I need but not figure out the correct syntax for expressing this in UnO2 Control Centre. I am att

Any advice on the best simple 1-in x 1-out MIDI to USB connecting my Gordius midi controller and iPad. I see a few likely options, and want the best iConnectivity mio Roland UM-ONE-MK2 FORE MIDI to US

I just bought FCB1010 with UNO chips and the editor to control BIAS FX 2 for IPAD; And I'm completely lost. Is somebody using it and could help me for the setup ? Thx a lot !

Hi all, have been an FCB1010 owner for some 18 years now... same unit, still going strong! I'm thinking of getting an Uno2 chip and was just wondering what the situation is regarding firmware versions

Hi. Have a couple of fcb units. One original firmware(latest) and one with uno 1. Is it correct that the editor from uno website, can manage units with both the uno1 and 2 and the original Behringer f

Hello, I'm Marco Hermans from Holland and I have a few questions about the Uno chip. I've recently purchased a brand new Behringer FCB1010. I hope it will arrived by the end of the week. I want to use

The following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /UnO2 BIAS Katana.txt By: jeffpagnutti@... Description: Control your Boss Katana and BIAS FX2!

Hi All. Looking for some help with sending note on commands to trigger chases on a simple lighting (hardware) controller please. I want to be able to tell the controller to (for example): Run chase nu

The following files have been uploaded to the Files area of the uno@fcb1010.groups.io group. /FCB1010 Schematic (revised).pdf By: Michael Whocares <the_crimson_thunder@...> Description: I took some ti