Can anyone tell me where I can find version 1 of the editing software for Windows? Thank you.

Half venting here, and half asking for help... I had been happily using ControlCentre V1 to program my UnO1s, but recently purchased two UnO2s and successfully created a config for one of my rigs. My

Hi All; I'm trying to setup an effect switch with an if...else condition check. First, if I type "if", the following pick list does not include the pre-defined "EFFECT_ON" or "EFFECT_OFF" variables, s

2 Questions 1. Is there a conversion kit still available for the FCB1010? 2 Is a regular 7-pin DIN cable compatible and/or the same thing as a 7-Pin Midi cable? TIA BI

Hi. How to calibrate the expression pedals with the Uno v1.0.4 ? The Uno manual contains any information about this procedure. May be, we have to refer to the Behringer procedure… Best regards. Pierre

Hi. Can we put back the original FCB1010 eprom without encountering any problem after having used the Uno eprom in the FCB ? This question comes to me because we have to initialize the Extended memory

So, I am trying to get my fcb1010 with UnO mod to worok properly. I don't have a gui, so I've been trying to program it using the board itself. I have some questions... If I have UnO installed, am I c

Hello, I need help with the code: I want to use the FCB1010 with the UnO2 Chip, with Cubase and plugins. I really tried hard to solve this riddle, but man, please, I need support! :D I created a pdf-d

FCB1010 Groups Running Costs 2022-2023 Requested By: Roger Colwell Description: This group was created in GIO in October 2019, from Yahoo Groups, due to the impending removal of all the stored informa

Hello, yet another newbie with a potentially dumb question, I apologize if this has been already answered somewhere else, I was unable to find it. I have a M-Audio Oxygen49 controller connected to the

Hi, I’m not sure if this is how or where to post questions. I’m NEW to MIDI. I’ve never used MIDI in any devices I’ve had over the years. I’m older in my 50’s and not hip slick or cool. Just humbly st

I wanted to know if I need to use the control center app instead of the fcb1010 editor. I renamed the at4from a lgp to the syx file and it went into the fcb and I can see it in the editor but not able

Hi experts, I am trying to do a loop where I increment the midi BPM. So it seemed logical to assign a initial BPM to a variable $BPM, say 10, then go into a while loop, use a wait statement and increm

Hi, I am only getting note off / 0 velocity notes. Two per press. Any ideas on what is wrong? I have an old uno version and using fcb control center. Thanks, Sam

Hey everyone, hoping someone can help me out. I set up my FCB1010 with UnO2 a long time ago. It works like a charm running MIDI into my Behringer UMC1820, with my basic 10-stompbox setup in ableton li

Just to be sure before I program a workaround - I guess it's not possible to activate / switchOn Presets through code, is it? (Like SwitchOn for Effects or SendTrigger for Triggers) That would be very

I am trying to create a preset that will send program change commands to advance the patch selection on my Minilogue, which seems to organize its patches into 4 banks of 100 patches each, numbered 0-9

tried it on my amd pc and my intel pc. have uno 1.4 installed into fcb1010. using ripwerx java. midisportr uno usb.. connected properly to in and out of fcb. when i run ripwerx and seletct midi ports

I have had a G Major 2 for quite a while and know it but have never used MIDI. I am seeking a write up guide for FCB1010 for using with G Major 2. I will be using it mosly in stomp box mode but will a

I agree this should be a new thread but as a complete novice on these boards I have no idea how to do this. Phil